✉ ronaldooyc@gmail.com|☎ 15861660221|Wuxi Base|Jiangyin Base|Zhejiang Base

November 17, 2026

Double-Sided Tape: Map Release-Side and Lamination-Side Data to the Assembly

When a double-sided tape specification gives separate data for “Release Side” and “Lamination Side,” first ask what those labels identify. Do not decide that one entry belongs to the floor, carpet, panel or component merely from its position in the table. A useful comparison connects each supplier label to one physical adhesive face and carries […]

Double-Sided Tape: Map Release-Side and Lamination-Side Data to the Assembly

When a double-sided tape specification gives separate data for “Release Side” and “Lamination Side,” first ask what those labels identify. Do not decide that one entry belongs to the floor, carpet, panel or component merely from its position in the table. A useful comparison connects each supplier label to one physical adhesive face and carries that identity through unwinding and assembly.

Haoxuan’s double-sided crepe paper tape listing identifies crepe paper, rubber adhesive on both faces and a yellow glassine liner. Its specification separates peel entries labeled Release Side and Lamination Side. These are catalog descriptions, not instructions for assigning a face to your application. Their definitions and test conditions require confirmation before the figures can support a purchasing decision.

Start with a physical reference, not a presumed installation rule

Give the received sample a unique identifier, including its product reference and any supplied lot information. Photograph the roll and a separate cross-section sketch without changing the original labeling. The drawing is a communication aid; it does not need to expose adhesive or damage a sample simply to create a picture.

Call the two adhesive faces A and B until the supplier confirms their terminology. Use a fixed edge, orientation arrow or other agreed reference to make the distinction reproducible. Avoid using “top” and “bottom” alone: those descriptions reverse when someone turns the material over. Face A should remain face A in every drawing, regardless of which direction the page is viewed.

Ask the supplier to mark which physical face corresponds to each specification entry. If the answer is provided on a photograph, retain that marked photograph with the specification revision. Do not translate an uncertain reply into a definitive assembly instruction. An unanswered mapping question should remain open in the sample review.

Show three stages of the same piece

The first drawing should show the tape as supplied, including the liner and winding reference where these are relevant. The second should show the first application stage and identify the exposed adhesive face. The third should show the finished assembly, with the other face and the liner-removal stage identified. These views describe the proposed workflow rather than prescribing how the tape must be installed.

Carry the same A and B identifiers through all three stages. A simple change of view can otherwise make it appear that the adhesive faces have switched. If the component is rotated or inverted between operations, draw that movement explicitly. The drawing should allow a second reader to trace each face without relying on an operator’s memory.

In a hypothetical two-panel assembly, one face may meet panel X during the first operation and the other meet panel Y later. That example explains the mapping method only. It does not establish which face Haoxuan recommends for either panel, or whether the proposed tape is suitable for those surfaces.

Keep substrate names separate from supplier face names

Add the actual substrate and finish beside each assembled interface. These describe the buyer’s intended use, while Release Side and Lamination Side describe entries in the supplier’s documentation. The two naming systems can be linked only after the physical mapping has been confirmed.

For carpet applications, the intended carpet and floor pair needs its own compatibility review. The key distinction remains: knowing which face contacts a surface does not prove that the bond or eventual removal will meet the project requirement.

Make each numerical comparison interpretable

Once the face labels are clear, request the method and conditions behind each data entry. Ask what test surface was used, which specimen construction was evaluated and how the reported result is expressed. Keep the supplier’s original units and terminology in the record; do not silently convert a value into a different test or application claim.

A higher reported figure should not become a “stronger side goes here” installation rule. Differences can only be interpreted within the stated test scope. The buyer’s substrate, application sequence and service conditions still need their own assessment by the responsible technical parties. This guide provides no peel threshold, preparation method or operating setting.

If a quotation uses a different face label from the sample sheet, ask for an explicit cross-reference. Similar numbers do not establish that the entries refer to the same physical face. A revised specification should identify what changed and whether the earlier mapping remains applicable.

Use a compact face-reference record

For each candidate, retain the sample ID, specification revision, face A definition, face B definition, supplier label for each face, liner position, first exposed face, intended substrate for each interface and the supplier’s confirmation. Add separate fields for test method and application-review status. This makes unresolved identity questions visible instead of burying them in email attachments.

Review the record with the person responsible for the actual assembly. Ask them to trace one piece from the roll to the finished part using only the drawing. If two readers produce different mappings, correct the documentation before comparing samples. The purpose is an unambiguous handoff, not a demonstration of bonding performance.

Keep a change log when the supply format, winding reference or assembly order changes. A familiar product name does not guarantee that a revised presentation can use the old drawing unchanged. Confirm the mapping again wherever the changed detail affects identification.

Send a question that the supplier can answer precisely

Send Haoxuan the marked sample reference, three-stage drawing, intended substrates, required dimensions, quantity and destination. Ask the supplier to identify Release Side and Lamination Side on that same drawing and provide the matching test documentation. Label any assumed mapping as unconfirmed rather than asking the supplier to approve an ambiguous description.

Use the Haoxuan inquiry page to request that clarification before final sample approval. A completed face map supports a clearer technical discussion; it is not a promise of suitability, clean removal or a particular bond result. Purchasing can then compare like-labeled evidence while the technical owner evaluates the complete proposed assembly.

Illustration note: The header image is a concept illustration, not a photograph of Haoxuan’s actual laboratory or evidence of actual product testing.